Groundwater Protection Regulation, B.C. Reg. 39/2016
Schedule 3
Schedule 3
Cite as Groundwater Protection Regulation, B.C. Reg. 39/2016, Schedule 3 · last amended December 1, 2022 · read from BC Laws on November 17, 2026
The text
Schedule 3
[am. B.C. Reg. 75/2021, s. 4.] Information in Well Construction Reports 1 A well construction report required under section 76 [well construction reports submitted to both comptroller and well owner] or 77 [well construction reports submitted to well owner only] of this regulation must include
(a) the following information relating to the owner and location of the well:
(i) the name, mailing address, telephone number and, if available, the email address of the owner of the well;
(ii) the property on which the well is located, described by its site address, legal description or parcel identifier number (PID);
(iii) either
(A) the universal transverse mercator (UTM) zone and the UTM coordinates of the well recorded to the nearest metre, or
(B) the latitude and longitude of the well recorded in decimal degrees to at least 5 decimal places or recorded in degrees, minutes and seconds with the seconds recorded to at least 2 decimal places,
(b) the following information relating to the type of work, class of well and method of drilling:
(i) whether the report relates to the drilling of, or an alteration to, the well;
(ii) the class and, if applicable, category or subclass of the well;
(iii) if the well is a water supply well, the intended use or purpose of the water supply well;
(iv) the method of drilling the well,
(c) the following information relating to geological materials and their water-bearing characteristics:
(i) a description of the geological materials encountered during drilling or alteration, including the depth at which the materials are encountered and whether they are water-bearing;
(ii) if the well is drilled into bedrock, the depth of water-bearing zones, if any, encountered in bedrock and their estimated flow,
(d) the following information relating to the construction of the well:
(i) the details of casings used, if any, including surface casing;
(ii) if a drive shoe was used;
(iii) the diameter of the hole;
(iv) the total depth drilled;
(v) the finished well depth;
(vi) the type and depth of any backfill materials or sealant placed in the well;
(vii) the details of the surface seal and the method of its installation, if a surface seal was installed;
(viii) the details of the screen assembly and filter pack material, if any;
(ix) the details of liner used, if any,
(e) if the well was developed, the following information relating to the development of the well:
(i) the method of development;
(ii) the duration of development,
(f) if a well yield test was conducted, the following information relating to the well yield test:
(i) the method, rate and duration of well yield testing;
(ii) the drawdown in water level at the end of well yield testing;
(iii) the well yield estimated from the test;
(iv) if the well was hydrofractured, any increase in well yield resulting from hydrofracturing,
(g) the following information relating to the completion of the well:
(i) if a casing was installed, the final length of the casing stick-up;
(ii) the static water level or shut-in pressure level, whichever is applicable;
(iii) whether the well was disinfected;
(iv) the type of well cap used, and if a well cover was also used, the type of well cover used,
(h) if a well identification plate is required, the following information:
(i) the well identification number;
(ii) the location where the well identification plate is attached,
(i) if available, the well tag number,
(j) the following information relating to the person responsible for drilling or altering the well:
(i) if applicable, the registration number of
(A) the person responsible for drilling or altering the well, and
(B) the person who drilled or altered the well, if different from the person referred to in clause (A);
(ii) the name and business contact information, including business name, if any, address, telephone number and, if available, email address and fax number of
(A) the person responsible for drilling or altering the well, and
(B) the person who drilled or altered the well, if different from the person referred to in clause (A),
(k) the starting and completion dates of the work,
(l) a copy of alternative specifications relating to the well, if any, made under section 18 (3) [siting of water supply wells and permanent dewatering wells] of this regulation, including the engineer's acceptance and the terms and conditions, if any, relating to the alternative specifications,
(m) a copy of the documentation referred to in section 19 (2) [siting of recharge wells and injection wells] of the regulation, including the design, the engineer's acceptance and the terms and conditions, if any, and
(n) a copy of any drilling authorization for the well. 2 Section 1 of this Schedule does not limit any other provision of this regulation requiring the inclusion of information in a well construction report.
Read the Groundwater Protection Regulation on BC Laws ↗
Made under Water Sustainability Act, SBC 2014, c. 15.