Occupational Health and Safety Regulation, B.C. Reg. 296/97
Schedule 8-A
Schedule 8-A
Cite as Occupational Health and Safety Regulation, B.C. Reg. 296/97, Schedule 8-A · last amended September 1, 2027 · read from BC Laws on November 17, 2026
The text
Schedule 8-A
[en. B.C. Reg. 312/2010, App. F, s. 2.]
(section 8.21 [leg protection])
WorkSafeBC Standard — Leg Protective Devices 1 This standard provides specifications and performance criteria for leg protection for a worker using a chain saw. 2 In this standard, “leg protection” or “leg protective device” means personal protective equipment worn for protection from leg injury due to contact with a moving saw chain. 3 Leg protection must be of one of the following types:
(a) pant type: the protective pad is secured to and held in position by the trousers;
(b) apron type: the protective pad is secured to an apron style garment normally worn outside the trousers and secured around the worker's legs and waist;
(c) chap type: the protective pad is secured to a chap style garment normally worn outside the trousers and secured around the worker's legs. 4
(1) Leg protection must be of materials suitable for the intended application.
(2) Leg protection
(a) must not unduly restrict the manoeuvrability of the worker, and
(b) must not shrink more than 10% when cleaned in accordance with the manufacturer's instructions during its service life.
(3) The protective pad of leg protection must be at least 711 mm (28 in.) long and of a width covering 180° in the front of both legs from inseam to outseam plus 100 mm (4 in.) on the left side of both legs.
(4) If the length requirement in subsection (3) results in a tripping hazard, the protective pad may be shorter, as long as it meets the requirements set out in subsection (5).
(5) When leg protection is worn by a worker, the protective pad
(a) must extend at minimum from the crotch to within 75 mm (3 in.) of the ankle, and
(b) must be effectively secured in this position.
(6) Effective measures must be taken to prevent unravelling or fraying of material along any edges or other area of leg protection where unravelling or fraying is likely to occur.
(7) A heat seal used to control unravelling or fraying of synthetic fibres of leg protection
(a) must be effective over the life of the product, and
(b) if subject to cracking, must be covered to prevent abrasion of the worker's skin.
(8) Instructions on the proper care, maintenance and repair of leg protection must be provided by the manufacturer.
(9) Leg protection showing damage that will affect its performance must be removed from service. 5
(1) Leg protection must meet or exceed the "threshold chain speed test" in which the protective pad must be able to consistently resist being cut-through by a running saw chain operating at a speed of 1 098 m/min (3 600 ft./min) or more for at least 1.01 seconds.
(2) Threshold chain speed tests must be conducted
(a) on leg protection samples assembled in the manner in which the leg protection will be produced for distribution, and
(b) using the test apparatus described in subsection (3) in accordance with the procedures and methodology described in this section.
(3) The test apparatus to be used in conducting a threshold chain speed test must include a simulated "leg", chain saw and instruments as follows:
(a) a simulated "leg" (see Figure 1) that is
(i) made of wood approximately 150 mm (6 in.) in diameter with a 20 mm (3/4 in.) layer of resilient covering (Ensolite or similar material) attached to simulate the resilience of flesh,
(ii) designed to allow the leg protection to be mounted and tested similar to the configuration the leg protection will take when worn by a worker while the worker's leg is extended, and
(iii) mounted to allow rotation about the longitudinal axis of up to 75 mm (3 in.) at the outer circumference, against an applied torque of at least 1.7 Newton-metres (15 inch pounds) and which torque may increase as the leg rotates;
(b) a chain saw, with Oregon 72 LP chisel chain and capable of a chain speed of at least 1 220 m/min (4 000 ft./min), that must pivot in a vertical plane to contact the "leg" (see Figure 1) with a downward force of 50 ± 1 Newtons (11 ± 0.1 lb.);
(c) instruments to measure and record chain speed and cut-through time.
(4) The test procedure and methodology are as follows:
(a) start the saw and set the chain speed to the constant level selected for the test cut;
(b) allow the bottom of the running saw chain to freefall 6 mm (1/4 in.) onto the test specimen mounted on the "leg";
(c) record the time from contact of the saw chain with the test specimen to the nearest 0.01 second;
(d) record the chain speed during each test;
(e) repeat the tests on the same material until the maximum chain speed (± 15 m/min or ± 50 ft./min) at which cut-through does not occur for at least 1.01 seconds or more is determined;
(f) maintain the chain saw in good repair throughout the testing and keep the saw cutters sharp in accordance with the saw chain manufacturer's recommendations.
Read the Occupational Health and Safety Regulation on BC Laws ↗
Made under Workers Compensation Act, RSBC 2019, c. 1.