Subdivision Regulations, B.C. Reg. 262/70
Schedule 1
Appendix A
Cite as Subdivision Regulations, B.C. Reg. 262/70, Schedule 1 · last amended February 24, 2022 · read from BC Laws on November 17, 2026
The text
Appendix A
[am. B.C. Reg. 4/2010, s. 3.]
(Section 4.08) 1 In this Appendix, unless the context otherwise requires:
“arterial” means a highway intended to carry large volumes of traffic at medium and high speeds primarily between major traffic generators, and it is not intended to directly serve adjacent land;
“collector” means a highway located within an area of major traffic generation and which is used primarily for the collection and distribution of traffic between arterials and locals as well as to some adjacent land;
“K value” means the distance required in feet to effect a 1% change in gradient on a vertical curve;
“local” means a highway located within an area of major traffic generation and used primarily to provide access to adjacent land. 2 The likely or intended use of the land, the climate prevailing in the area, the relation of the subdivision to the surrounding highway system, the topography and the necessity for on-street parking shall be taken into account, and design speed and finished grade width of roadway set accordingly as in sections 3 and 4 of this Appendix. 3 Parameters for various design speeds shall be as follows: Design Speed 20 mph. 30 mph. 40 mph. Maximum curvature (degrees) 52 22.9 12.4 Minimum stopping sight-distance (feet) 120 200 275 K value crest (vertical curves) 15 28 50 K value sag (vertical curves) 19 35 50 Overhead clearance (feet) 15 15 15 Maximum grade (per cent) 12 8 8 Maximum superelevation (per cent) 10 8 8 Maximum grades are to be reduced by 1% of grade for each 100 feet
of radius below 500 foot radius curve (11 29'). 4 Finished road grade width shall be 32 feet for local roads with parking and also for arterials and collectors and 24 feet for other roads. A finished grade width of 20 feet may be approved in special circumstances by the approving officer. Side slopes in surfacing and subgrade are not to be steeper than 2:1. 5 Drainage is to be adequate in the opinion of the approving officer, and all ditches, pipes, etc., are to be carried to natural drainage features as far as possible. 6 All ditch inverts are to be minimum 3 feet below centre line elevation of roadway. 7 All drainage facilities, including culverts, are to be designed for 30 year flood in urban areas, suburban areas and rural areas likely to grow into suburban areas and in all other areas to be designed for 10 year flood. 8 Any drainage appurtenances shall conform to C.S.A. or A.S.T.M. specifications for the purpose for which it is intended. 9 All bridges and span or box culverts are to be designed by a professional engineer to AASHO H20S16 loading for local roads, and to AASHO H25S20 loading for collectors and arterials. 10 With the exception of those trees and shrubs the District Highway Manager of the ministry of the minister responsible for the administration of the Transportation Act approves as worthy of preservation and which are located close to the edge of a highway allowance intended for vehicular use, the full width of all highways shall be cleared and grubbed. Brush, debris, stumps and roots shall be disposed of to the satisfaction of the District Highway Manager of the ministry of the minister responsible for the administration of the Transportation Act. 11 Roads shall be surfaced in 2 courses:
(a) a lower course composed of select granular material passing 3 inch mesh as per Ministry of Transportation Highways specification 202.7, and
(b) an upper course composed of a minimum of 3 inches of 3/4 inch crushed or screened aggregate, as per Ministry of Transportation and Highways specification 202.4,
and the minimum depth of the 2 courses shall be 6 inches. Where more material is required to build a sound and uniform roadway, the lower course shall be increased in depth. 12 The approving officer may also require asphaltic or portland cement concrete surfacing as per Ministry of Transportation and Highways specification, sections 220, 222 and 223, to a width not less than 4 feet narrower than the finished road grade width (see section 4). 13 All construction practice and procedure shall be generally to the standard of the Ministry of Transportation and Highways General Specifications.
Read the Subdivision Regulations on BC Laws ↗
Made under Local Services Act, RSBC 1996, c. 276.