HR 5741 — TRUMP Act of 2025

(a) The Secretary of the Treasury may mint and issue only the following coins: (1) a dollar coin that is 1.043 inches in diameter. (2) a half dollar coin that is 1.205 inches in diameter and weighs 11.34 grams. (3) a quarter dollar coin that is 0.955 inch in diameter and weighs 5.67 grams. (4) a dime coin that is 0.705 inch in diameter and weighs 2.268 grams. (5) a 5-cent coin that is 0.835 inch in diameter and weighs 5 grams. (6) except as provided under subsection (c) of this section, a one-cent coin that is 0.75 inch in diameter and weighs 3.11 grams. (7) A fifty dollar gold coin that is 32.7 millimeters in diameter, weighs 33.931 grams, and contains one troy ounce of fine gold. (8) A twenty-five dollar gold coin that is 27.0 millimeters in diameter, weighs 16.966 grams, and contains one-half troy ounce of fine gold. (9) A ten dollar gold coin that is 22.0 millimeters in diameter, weighs 8.483 grams, and contains one-fourth troy ounce of fine gold. (10) A five dollar gold coin that is 16.5 millimeters in diameter, weighs 3.393 grams, and contains one-tenth troy ounce of fine gold. (11) A $50 gold coin that is of an appropriate size and thickness, as determined by the Secretary, weighs 1 ounce, and contains 99.99 percent pure gold. (12) A $25 coin of an appropriate size and thickness, as determined by the Secretary, that weighs 1 troy ounce and contains .9995 fine palladium. (b) The half dollar, quarter dollar, and dime coins are clad coins with 3 layers of metal. The 2 identical outer layers are an alloy of 75 percent copper and 25 percent nickel. The inner layer is copper. The outer layers are metallurgically bonded to the inner layer and weigh at least 30 percent of the weight of the coin. The dollar coin shall be golden in color, have a distinctive edge, have tactile and visual features that make the denomination of the coin readily discernible, be minted and fabricated in the United States, and have similar metallic, anti-counterfeiting properties as United States coinage in circulation on the date of enactment of the United States $1 Coin Act of 1997. The 5-cent coin is an alloy of 75 percent copper and 25 percent nickel. In minting 5-cent coins, the Secretary shall use bars that vary not more than 2.5 percent from the percent of nickel required. Except as provided under subsection (c) of this section, the one-cent coin is an alloy of 95 percent copper and 5 percent zinc. In minting gold coins, the Secretary shall use alloys that vary not more than 0.1 percent from the percent of gold required. The specifications for alloys are by weight. (c) The Secretary may prescribe the weight and the composition of copper and zinc in the alloy of the one-cent coin that the Secretary decides are appropriate when the Secretary decides that a different weight and alloy of copper and zinc are necessary to ensure an adequate supply of one-cent coins to meet the needs of the United States. (d) (1) United States coins shall have the inscription “In God We Trust”. The obverse side of each coin shall have the inscription “Liberty”. The reverse side of each coin shall have the inscriptions “United States of America” and “E Pluribus Unum” and a designation of the value of the coin. The design on the reverse side of the dollar, half dollar, and quarter dollar is an eagle. Subject to other provisions of this subsection, the obverse of any 5-cent coin issued after December 31, 2005, shall bear the likeness of Thomas Jefferson and the reverse of any such 5-cent coin shall bear an image of the home of Thomas Jefferson at Monticello. The Secretary of the Treasury, in consultation with the Congress, shall select appropriate designs for the obverse and reverse sides of the dollar coin. The coins have an inscription of the year of minting or issuance. However, to prevent or alleviate a shortage of a denomination, the Secretary may inscribe coins of the denomination with the year that was last inscribed on coins of the denomination. (2) The Secreta...