General, N.B. Reg. 91-191

Section 142

Fixed support

Cite as General, N.B. Reg. 91-191, s. 142 · current to June 30, 2026 · read from New Brunswick Acts and Regulations on November 16, 2026

The text

(1) An employer shall ensure that swing staging and boatswain’s chair, when attached to a fixed support, are capable of supporting at least four times the maximum load to which the fixed support is likely to be subjected (a) without overturning, and (b) without exceeding the allowable unit stresses for the material used in the fixed support. (2) An employer shall ensure that (a) a hook used to suspend swing staging or boatswain’s chair (i) has safety devices to prevent dislodgement, and (ii) is securely tied back to an anchor point capable of preventing the movement of the suspended equipment, and (b) a thrust-out used to suspend swing staging or boatswain’s chair (i) is rigidly fastened to another thrust-out, (ii) is securely tied back to an anchor point capable of preventing the movement of the suspended equipment, (iii) is counter-balanced with sufficient solid material to ensure stability, and (iv) has cleats or bolts fastened at the outer ends of the thrust-out to act as safety stops. (3) An employer shall ensure that rope made of synthetic fibre or wire used to suspend swing staging or a boatswain’s chair (a) provides a safety factor of not less than ten, based on the ratio of the manufacturer’s rated breaking strength of the rope to the static load, (b) is securely fastened to the drum of a winch, and is of sufficient length to allow for at least three turns of rope on the drum when the swing staging or a boatswain’s chair is in its lowest position or in accordance with the manufacturer’s specifications, and (c) is removed from use in accordance with the manufacturer’s specifications. (4) An employer shall ensure the materials used to support swing staging or a boatswain’s chair meet the following requirements: (a) if hangers are used, the hangers are made of wrought iron or mild steel with a cross section equal to 10 mm by 32 mm or a diameter of at least 19 mm and are securely attached to the platform or chair; (b) if wire rope is used, the wire rope is at least 13 mm in diameter for the swing staging and 9 mm for the boatswain’s chair; and (c) if another material is used, it has been certified by an engineer as being of a strength equivalent to that prescribed in paragraph (a) or (b). (5) An employer shall ensure that the platform of swing staging is not less than 500 mm in clear width and is either a ladder type platform or a plank type platform. (6) An employer shall ensure that the side stringers, rungs and tie rods of a ladder type platform for swing staging conform to the following table: LADDER TYPE PLATFORMS FOR SWING STAGING LengthofSideStringers | WidthBetweenSideStringers | Cross Section ofSide Stringers | Rungs | Tie Rods At Ends | At Middle | TotalNo. | Diameter | TotalNo. | Diameter 4.6 m | 500 mm | 50 mm × 70 mm | 50 mm × 100 mm | 10 | 30 mm | 4 | 8 mm 4.9 m | 500 mm | 50 mm × 70 mm | 50 mm × 100 mm | 11 | 30 mm | 4 | 8 mm 5.5 m | 500 mm | 50 mm × 80 mm | 50 mm × 100 mm | 12 | 30 mm | 4 | 8 mm 6.1 m | 500 mm | 50 mm × 80 mm | 50 mm × 100 mm | 13 | 30 mm | 4 | 8 mm 7.3 m | 500 mm | 50 mm × 80 mm | 50 mm × 120 mm | 16 | 30 mm | 5 | 8 mm (7) An employer shall ensure that the flooring of a ladder type platform on swing staging is at least 19 mm thick plywood or another material of equivalent strength. (8) An employer shall ensure that the planks in a plank type platform on swing staging (a) are made of wood and are a uniform thickness of not less than 50 mm, (b) are tied together on the underside by cleats (i) a minimum size of 25 mm by 150 mm, (ii) securely fastened, and (iii) spaced at intervals of not more than 1.2 m, (c) do not exceed 3.7 m in length, and (d) are located so that the span does not exceed 3 m between the fixed supports. (9) An employer shall ensure that (a) swing staging is equipped with a guardrail, (b) two or more pieces of swing staging are not joined together, and (c) swing staging is lowered to the ground or lashed to the building to which it is attached when employees leave the building.
Read the General on the Province's website ↗

Made under Occupational Health and Safety Act, c. O-0.2.