Hazardous Waste Regulation, B.C. Reg. 63/88

Section 42

Pest control product wastes and containers

Cite as Hazardous Waste Regulation, B.C. Reg. 63/88, s. 42 · last amended July 1, 2026 · read from BC Laws on November 17, 2026

The text

(1) In this section: “appropriate solvent” means a solvent that does not contain a pest control product and is capable of dissolving or removing a pest control product; “empty” means (a) to drain a liquid product residue from a container into a spray tank or mixing tank for a period of not less than 30 seconds, (b) to remove an inner liner, where present, and shake all product residue into a spray tank or mixing tank, or (c) to use all the product in a pressurized metal container without puncturing the container; “pressure rinse” means to clean by means of pressurized spraying of an appropriate solvent into an empty container for at least 30 seconds so that all interior surfaces of the container are rinsed; “product” means pest control product; “rinse” means (a) to introduce an appropriate solvent into an empty container in an amount not less than 20% of its volume, (b) to close and shake the container so that the solvent makes contact with all interior surfaces, and (c) to open and empty the container. (2) Subject to this section, the disposal of (a) a waste product container, and (b) a waste containing a product is authorized. (3) A waste containing a product is designated as a hazardous waste if (a) the waste fits the criteria for classes 3 to 6.1, 8 or 9 of the federal dangerous goods regulations, or (b) the aquatic toxicity (the 96 hour LC50) of the waste is less than 500 mg/L as measured by methods that are approved in accordance with section 49. (4) A waste product container that is (a) emptied and rinsed in the manner set out in this section, or (b) labelled "Domestic" by the manufacturer and emptied is not a hazardous waste. (5) Prior to disposal of a waste product container, the owner of it must (a) empty the container, and (b) rinse it using the appropriate method indicated in the following table: TABLE Methods for Rinsing Waste Pest Control Product Containers Item Type of Container Rinsing Method 1 Rigid plastic or metal (nonpressurized) Pressure rinse, or single rinse 3 times 2 Rigid plastic or metal (pressurized) No rinsing required 3 Glass bottle Rinse 3 times 4 Paper bag Rinse 5 Plastic bag Rinse 6 Containers labelled "Domestic" No rinsing required 7 Any container type not listed above As approved (6) The owner of a waste product container that has been emptied and rinsed must recycle the container or dispose of it (a) in an approved landfill, or (b) by burying it, but only if (i) the burial location (A) is on land owned or leased by the person owning the container, or (B) is on land owned, leased or maintained in a tree farm licence, as defined in the Forest Act, by the person owning the container, (ii) the burial location is on flat ground, not in a swale and at least 200 m from surface water or a well, (iii) the ground does not consist of gravel, sand or other similarly porous material, and (iv) the owner covers it with at least 0.5 m of soil immediately after burial. (7) Waste produced by cleaning pesticide application equipment or by rinsing waste product containers under this section must, if practicable, be used in mixing a product solution but, if not practicable, it may be applied to land if the area to which it is applied (a) is on land to which the product contained in the waste has been applied for purposes of pest control, (b) is flat ground, not in a swale, and at least 200 m from surface water or any well, and (c) does not consist of gravel, sand or other similarly porous material.
Read the Hazardous Waste Regulation on BC Laws ↗

Made under Environmental Management Act, SBC 2003, c. 53.