Mineral Tenure Act Regulation, B.C. Reg. 529/2004

Schedule A

Schedule A — Guidelines for Reporting Exploration and Development Work

Cite as Mineral Tenure Act Regulation, B.C. Reg. 529/2004, Schedule A · last amended March 11, 2021 · read from BC Laws on November 17, 2026

The text

Schedule A — Guidelines for Reporting Exploration and Development Work [am. B.C. Reg. 78/2008, Sch. B, s. 6.] 1 (1) In this Schedule, “report” means a report referred to in subsection (2). (2) This Schedule defines the form and medium for a report required by section 33 of the Mineral Tenure Act and section 16 of the Mineral Tenure Act Regulation. (3) This Schedule applies to the reporting of (a) technical exploration and development as defined in section 1 of the Mineral Tenure Act Regulation, and (b) the following exploration and development activities: (i) determining ownership of land; (ii) serving notice under section 19 (1) of the Act; (iii) making reasonable efforts to serve notice under section 19 (1) of the Act if an exemption has been granted under section 19 (1.1) of the Act. 2 (1) All text and map information in a report must be presented so that the location and the results of the investigation are clear and legible. (2) The report must be typed on a good grade of standard letter size paper secured in a binder and the margins must be wide enough to allow for complete visibility of all text. (3) Pages must be easily removed from the binder. (4) The report must contain the following: (a) a title page; (b) a table of contents; (c) an introduction; (d) technical data and interpretation; (e) drill logs and diagrams; (f) an itemized cost statement; (g) a statement of the author's qualifications; (h) a list of references cited in the report; (i) a list of software programs used in support of the exploration and development and the preparation of the report. (5) The title page must do all of the following: (a) identify the general nature of the report; (b) briefly identify the specific claims involved; (c) identify the relevant mining division; (d) specific the NTS or BCGS location; (e) specify the latitude and longitude or UTM zone, easting, and northing coordinates representing the geographic centre of the assessment work; (f) name the owner of the claims; (g) name the operator (who paid to have the work done); (h) name any consultant involved in the matter; (i) name the author of the report; (j) specify the date the report is submitted. (6) A table of contents must identify all text pages, sections, diagrams, drill logs or any other documentation by sequentially numbered pages, including numbered appendices, maps, figures and other illustrations and any itemized cost statement. (7) An introduction must include the following: (a) the general geographic and physiographic position of the claims, access to the claims and index map; (b) the property definition, containing history of the property, current owner, operator, brief economic assessment of property, etc.; (c) for each type of work, a list of claims including tenure numbers on which work was actually performed; (d) a summary of work done as follows: (i) for geochemical survey, the total number of soil, silt or rock chip samples collected, separately listed; (ii) for geophysical survey, the total number of kilometres of line surveyed for each type of survey; (iii) for drilling, the size and number of holes reported on and the total metres of drilling reported; (iv) for geological survey, the scale of mapping and the total area surveyed; (v) for a topographic survey, the total area surveyed; (vi) for prospecting, the total area prospected; (vii) for linecutting or grid establishment, the total number of kilometres of line cut or established. (8) Technical data and interpretation as determined by the investigation, the purpose, results, interpretation and conclusions as required in this Schedule must be included in the report. (9) The author's qualifications must be documented for all reports. 3 (1) The index map must accurately show the maximum footprint of the area investigated in relation to identifiable geographic features using published topographic maps at a standard scale of 1:50 000 or more detailed and labelled with NTS or BCGS designation. (2) The footprint of each plan map showing results must be keyed to the index map by showing on both maps sufficient common geographic features such as lakes, streams, railways, roads, settlements, etc. (3) The area investigated, meaning the grid surveyed, diamond drill holes, sample locations, areas mapped, etc., must be shown in relation to boundaries or legal posts of the named mineral claims either on the plan maps or on a separate claim map which must be at a scale of 1:10 000 or more detailed. (4) Each plan map and index map must show orientation with respect to astronomic north and a bar scale. (5) Sections, profiles and other diagrams must show appropriate co-ordination scales. (6) Each drawing and map must show an identifying title and sufficient legend to be fully comprehensible. (7) Maps must measure not greater than 120 cm in one direction and 90 cm in the other. 4 (1) Exploration and development assessment work reports may be submitted as Portable Document Format (PDF) Adobe Acrobat 5.0 (or higher) compatible files. (2) The form, content and layout should be exactly the same for the report as that of a hard copy report as defined by Sections 2 and 3 of this Schedule. (3) Text, maps, charts, figures, photographs and tables should be converted into PDF format directly from the application in which they were created. (4) Assays and analyses received as digital files from geochemical laboratories should be converted to PDF format and inserted into the report. (5) A digital copy of the assays and analyses may also be included as an MS Excel file as a separate appendix to the document. (6) Raw geophysical data may also be included as separate files in the format supplied by the geophysical contractor. (7) Data that can not be converted directly to a PDF file must be scanned to all of the following specifications: (a) a minimum of 200 dots per inch (dpi); (b) converted to Adobe Acrobat 5.0 format; (c) imbedded into the report in the proper sequence. (8) In creating a PDF document, the author must not do any of the following: (a) assign any passwords or set any document security controls for any PDF document; (b) create "article threads" in any PDF document; (c) add form fields or form actions to a PDF document; (d) add JavaScript to a PDF document; (e) add page actions to a PDF document; (f) annotate a PDF document including embedding or attaching files, text, graphics other than maps or figures required for the report, audio or video files or annotations created with various other mark-up tools. (9) URL links may be included in the text for reference purpose only, but only if the URL is hyperlinked and the link is not used as a substitute for data. (10) The report must be digitally signed by the author and saved as a certified document. (11) If reports in digital format can not be submitted electronically because the electronic portal is not available, reports may be submitted on CD-ROM media (phthalocyanine based dye, gold based reflective layer) written in ISO 9600 format, and byte-by-byte verified against original image files. 5 (1) Observations made during the investigation must be set out in a typewritten description and signed by the prospector who performed the work. (2) A map or maps, at a scale of 1:5 000 or more detailed, must be submitted and must include the following: (a) a bar scale and true north arrow; (b) the location of claim posts and boundaries relative to identifiable geographic features, including named streams, lakes, roads, settlements, bridges and railroads; (c) the location of traverses; (d) the location of all instrument readings with the corresponding values obtained; (e) the location of all samples with the corresponding assay results; (f) the location of, and a geological description of, each outcrop or area of boulders investigated. 6 (1) The lithology and structure of the rocks and any mineralization observed in them must be described in text. (2) Ore minerals, such as chalcopyrite must be fully named rather than being reported as copper mineralization. (3) The report on geological mapping must include the following: (a) a geological map or maps which show the location and outline of outcrops; (b) the name of the rock exposed; (c) significant geological structures and mineralization; (d) a legend which identifies the symbols used and the rock types; (e) the units on the map coded with numbers or patterns to conform with numbered or patterned map units in the legend. (4) Geological mapping of underground workings must include the outline of the workings and the geological observations must be shown on a plan or plans at a standard scale of 1:1 000 or more detailed. (5) For the purposes of subsection (4), two or more levels may be shown only if their data do not overlap. (6) If there are raises, stopes and other non-horizontal workings, (a) they must be shown in section, (b) the elevation of the workings must be provided, (c) multiple workings must be tied together with a co-ordinate system, and (d) a surface plan must be included which adequately ties the workings into identifiable surface features and the index map. (7) Geological mapping of trenches that expose bedrock must show the outline of the trenches and describe the geological observations as set out above. (8) Descriptions and coordinates in NTS or UTM systems of all samples taken for analysis or examination must be included. 7 (1) The field sampling procedure, the quality control and the materials sampled must be described. (2) Descriptions and coordinates in NTS or UTM systems of all samples taken for analysis or examination must be included. (3) Soil horizons must be identified and the sample depth stated. (4) Drainage sediment samples must indicate the drainage type (lake bottom, stream, moss mat or heavy mineral) and the location in the stream or lake from which the samples are taken must be recorded. (5) Sampled bedrock must be identified as to rock type. (6) If the sampling method is new and not described in readily available literature, the text must include a statement of the underlying theory, a full description of instrumentation, measurement and data reduction, and results from test areas. (7) A biogeochemical survey must identify the species and part of the plant sampled. (8) The results must be shown in a plan that sets out the numerical values obtained and their location, but for isolated or widely spaced sampling traverses, the results may be shown in profile. (9) The plan must clearly identify each value with its element and state the unit of measurement. (10) If sampling was done in 2 or more separate periods, the values must be distinguished by suitable symbols. (11) The report must contain the following information: (a) the name of the analytical laboratory or chemist who did the analyses; (b) the mesh size fraction of the sample used for analysis; (c) the name and concentration of reagents used for extracting from the sample each element tested; (d) the chemical procedure for testing the samples; (e) if the samples were tested in the field, a description of the procedure; (f) in a biogeochemical report a description of the ashing technique. (12) The report must contain an interpretation and evaluation of the geology, soil types and topography reported. (13) Reports on airborne geochemical surveys must include all of the following: (a) a full description of the procedure and sensing method; (b) the results of control surveys over known ore and known barren ground; (c) the results in an organized form; (d) a description of the flight lines in relation to identifiable surface features; (e) a statement of the ground speed and clearance of the aircraft; (f) the meteorological conditions, particularly wind speed and direction, air temperature, humidity and percentage and thickness of cloud cover; (g) a description of the vegetation. 8 (1) The method and procedure must be stated and the make and model of geophysical instruments must be given so that the characteristics of the instruments may be known from a catalogue or similar source of information. (2) If the method is new and not described in readily available literature, the text must include a statement of the underlying theory, a full description of instrumentation, measurement and data reduction, and results from test areas. (3) The units of measurement and the units in which the results are presented must be clearly stated. (4) Spurious results from a malfunctioning instrument must be omitted. (5) Suspect results must be identified by a suitable symbol or note. (6) The report must contain a drawing or drawings showing the numerical values obtained and their location. (7) If the results are presented in profile or pseudo profile form, a plan map is required at a scale of 1:12 000 or more detailed, showing the survey grid in relation to the claims and sufficient surface features to correlate the plan map with the index map. (8) The report must contain an interpretation and evaluation of the geology, soil types and topography reported. (9) In a report on a magnetic survey (a) the map or profiles must show whether the values represent the total intensity of the magnetic field or the vertical component, (b) the map or profiles must show whether the values are absolute or relative, and the units in which these values are recorded, (c) the text must state whether the values were corrected for diurnal variation and the method used to achieve this correction, (d) the values so corrected constitute basic data and must be submitted, and (e) results of any other mathematical treatments must be shown on separate drawings. (10) In a report on an electromagnetic survey, the method and array must be clearly identified. (11) The location of the transmitter for a very low radio frequency (VLF) survey must be stated. (12) In a report on an induced polarization survey, the specific method and the electrode array used must be stated. (13) For an airborne geophysical survey by appropriate recognized methods, (a) the results must be presented in contour form on the geophysical map rather than as numerical values, (b) the geophysical map must be at a standard scale of 1:50 000 or more detailed, (c) the geophysical results and the flight lines must be accurately located in relation to each other and the claims and identifiable geographic features, and (d) the terrain clearance must be stated. 9 (1) A report respecting drilling activity must include a statement of the purpose of the drilling program and an interpretation of the results containing stratigraphic or lithologic information. (2) Each copy of a drilling report must contain the following information: (a) a surface or underground plan at a standard scale of 1:5 000 or more detailed, showing the location of the drill hole collars in relation to claim unit boundaries and identifiable surface features or underground workings; (b) the inclination and azimuth, dip tests, core diameter for diamond drill holes and collar elevation, if known, of each drill hole; (c) for diamond drill holes, clearly legible (preferably typewritten) copies of drill core logs for all drilling submitted for credit; (d) in the logs referred to in paragraph (c), a list of all minerals noted in the core; (e) cross-section drawings at a scale of 1:500 or more detailed showing the total depth, lithologies or stratigraphy and mineralization with assays intersected in each hole, including correlations, if reasonable, between holes on the same cross-section; (f) for diamond drill holes, a statement of the location of the core storage; (g) for percussion drill holes, the depth of overburden and a cuttings log or similar description of rock types and minerals encountered; (h) if geophysical logging has been conducted in drill holes (for example, radiometric) a copy of those logs. (3) If assays of core or cuttings are done, the complete assay results must be correlated and submitted along with the logs. 10 Reports that contain results of sampling of minerals, bedrock outcrops, trenches, pits, underground workings, bulk samples, core, drill cuttings, geochemical samples sediments, overburden, soils, till, water, vegetation, flora, fauna or other environmental samples must include the following requirements: (a) the name and address of the analytical laboratory; (b) a statement of qualifications of the person who did the analyses; (c) the certificate of analysis, signed by the chemist who performed or supervised the analysis, that is included in the assessment report; (d) the sample preparation, analytical or chemical procedure, reagents, equipment and procedures including screening, crushing and milling processes; (e) the mesh size fraction, the split and weight of the sample used for analysis; (f) the laboratory's quality control procedures during sample preparation and analysis including the insertion of duplicates, standards, repeat analyses and any verification by repeat analyses at separate laboratories; and documentation of the sampling and analytical precision and accuracy of the results in the assessment report; (g) if the samples were tested in the field, a description of the procedure; (h) in a biogeochemical report, a description of the ashing technique; (i) for airborne geochemical surveys, a description of the procedure and sensing instrumentation used to remotely measure elemental concentrations, the data processing procedures, the flight lines shown in relation to identifiable surface features, ground speed and clearance of the aircraft, meteorological conditions (wind speed and direction, air temperature and humidity and percentage and thickness of cloud cover) description of vegetation and results of control surveys and correlations with elemental signatures of known mineralization and barren ground. 11 (1) A report of an archaeological impact assessment must include (a) the objective of the assessment, and (b) the findings of the assessment. (2) The report must generally adhere to the principles set out in section 14 of the Heritage Conservation Act. 12 (1) For the purposes of this section, “mineral resource”, “inferred mineral resource”, “indicated mineral resource” and “measured mineral resource” have the meanings given to those terms by the Canadian Institute of Mining, Metallurgy and Petroleum, in the Standards on Mineral Resources and Reserves Definitions and Guidelines adopted by CIM Council on August 20, 2000. (2) Estimates of mineral resources or mineral reserves must conform with standards, set by the Canadian Securities Administrators, known as National Instrument 43-101. 13 (1) A report of activities conducted in support of other technical exploration and development work must include a report of that other exploration and development work. (2) A report under subsection (1) must include the following: (a) metric dimensions of roads or trails together with details of their construction; (b) descriptions and full details of construction of improvements to existing roads or trails; (c) the metric dimensions of any helicopter sites, drill sites or core storage and a sketch of each site or core storage, all shown on the best topographic map available for the area; (d) a map at 1:20 000 scale or more detailed showing the activity in relation to the claim to which the work is to be applied and topographic detail for the area; (e) adequate documentation of ground control surveys, line cutting or grid establishment, topographic and photogrammetric mapping, satellite or other remote sensing in the manner required in other relevant provisions of this Schedule. 13.1 (1) A report about determining ownership of land must include the following: (a) a list of all the properties that were researched to determine ownership; (b) a statement of the actions taken to research the properties referred to in paragraph (a); (c) an itemized cost statement of the costs associated with the actions referred to in paragraph (b). (2) A report about (a) serving notice under section 19 (1) of the Act, or (b) making reasonable efforts to serve notice under section 19 (1) of the Act if an exemption has been granted under section 19 (1.1) of the Act must include an itemized cost statement of the costs associated with preparing the notice, serving the notice or making reasonable efforts to serve the notice, as applicable. 14 For the purposes of this Schedule, a cost statement must contain all of the following information: (a) number of days, rates per day, specific date and total wages paid every person employed; (b) number of days, rates per day, specific dates documenting food and accommodation charges for all persons employed during the investigation; (c) number of days, rates per day, specific dates and specific information on costs incurred from all forms of transportation and instrument rental required during the investigation; (d) number of days, unit rates, specific dates, specific information on all charges incurred by surveys conducted and total cost for all analyses performed during and subsequent to the investigation; (e) reasonable costs of preparation of the report pertaining to the investigation; (f) any other documented and itemized costs that have been incurred in carrying out the investigation.
Read the Mineral Tenure Act Regulation on BC Laws ↗

Made under Mineral Tenure Act, RSBC 1996, c. 292.