Commercial Transport Regulations, B.C. Reg. 30/78
Section 8.04
Pilot car signs
Cite as Commercial Transport Regulations, B.C. Reg. 30/78, s. 8.04 · last amended August 5, 2025 · read from BC Laws on November 17, 2026
The text
(1) In this section:
“SAE” means the Society of Automotive Engineers;
“SAE Standard J595” means SAE standard J595_202108 entitled Directional Flashing Optical Warning Devices for Authorized Emergency, Maintenance, and Service Vehicles, as amended from time to time;
“SAE Standard J845” means SAE standard J845_202108 entitled Optical Warning Devices for Authorized Emergency, Maintenance, and Service Vehicles, as amended from time to time.
(2) The operator of a pilot car must ensure that the pilot car is
(a) while escorting a vehicle or load, equipped with a roof-mounted "Long Load", "Wide Load", "Oversize Load" or "D" sign,
(b) while escorting a vehicle, or a vehicle and load, in excess of 27.5 m in length and less than 3.2 m in width, equipped with a roof-mounted "Long Load", "Oversize Load" or "D" sign, and
(c) while escorting a vehicle, or a vehicle and load, in excess of 3.2 m in width, equipped with a roof-mounted "Wide Load", "Oversize Load" or "D" sign.
(3) The operator of a pilot car must ensure that a sign described in subsection (2)
(a) meets the requirements of subsection (4),
(b) conforms to the specifications shown in Appendix K,
(c) is mounted on the pilot car so that the bottom edge of the sign, when in an upright position, is no less than 1.7 m and no more than 2.5 m above the road surface,
(d) is positioned perpendicular to the roadway while the pilot car is escorting a vehicle or load,
(e) is covered, blacked out, retracted or folded down while the pilot car is not escorting a vehicle or load, and
(f) does not adversely affect the normal operation of the pilot car on the highway.
(4) A sign described in subsection (2) must
(a) have a sign box or sign casing, made from durable material suitable for use in all weather and highway conditions that
(i) is 180 cm x 35 cm,
(ii) is evenly illuminated, and
(iii) shelters all wire connectors, switches, flashers and similar wiring components for the lighting attached to it,
(b) be designed to be mounted on roof-mounted carriers or similar mountings,
(c) be double-faced,
(d) be visible and legible from the front and rear of the pilot car from 300 m in clear conditions in daylight and darkness, and
(e) when used in darkness, have a luminance output that does not exceed 100 cd per square metre.
(5) The following may be dimmed to be visible and legible from less than 300 m in clear conditions:
(a) the rear face of a sign referred to in subsection (2) mounted on a pilot car immediately preceding an escorted vehicle or load;
(b) the front face of a sign referred to in subsection (2) mounted on a pilot car immediately following an escorted vehicle or load.
(6) The operator of a pilot car must ensure that either of the following is mounted on a sign referred to in subsection (2):
(a) 2 or 4 round amber flashing lamps;
(b) 2 round amber flashing lamps and 2 360° rotating or strobe amber flashing lamps.
(7) The round amber flashing lamps referred to in subsection (6) must
(a) flash in unison,
(b) meet SAE Standard J595 Class 2 yellow,
(c) be at least 17.75 cm in diameter, and
(d) be placed and operated as shown in Appendix K.
(8) The 360° rotating or strobe amber flashing lamps referred to in subsection (6) must
(a) meet SAE Standard J845 Class 2 yellow, and
(b) be placed and operated as shown in Appendix K.
(9) The operator of a pilot car, when so required by a peace officer, must provide evidence from the manufacturer of the sign referred to in subsection (2) that demonstrates that the luminance output of the sign does not exceed the luminance output specified in subsection (4) (e).
Read the Commercial Transport Regulations on BC Laws ↗
Made under Commercial Transport Act, RSBC 1996, c. 58.