Formaldehyde Emissions from Composite Wood Products Regulations, SOR/2021-148
Section 8
Quality control testing
Cite as Formaldehyde Emissions from Composite Wood Products Regulations, SOR/2021-148, s. 8 · current to July 24, 2025 · regulation last amended March 18, 2025
Statute Watch
Get an alert when a bill in Parliament would change this section, and every time it moves.
The text
(1) A manufacturer of composite wood panels or laminated products must, for each product type,
(a) select a specimen of its composite wood panels or laminated products, or have a specimen selected, in accordance with the requirements set out in subsections 12(1) and (2);
(b) test the specimen, or have the specimen tested, in accordance with a test method that yields results that have been correlated, under subsection (4), with the results obtained by using ASTM E1333 or, if equivalence is established under subsection 7(3), ASTM D6007; and
(c) have a third-party certifier verify the test.
(2) The selection and testing referred to in paragraphs (1)(a) and (b) must be performed
(a) in the case of hardwood plywood or a laminated product, for each product type,
(i) if the weekly amount manufactured is less than or equal to 9 290 m2, but more than 9 290 m2 is manufactured each month, once for every 9 290 m2 of the product type manufactured,
(ii) if the monthly amount manufactured is less than or equal to 9 290 m2, once during every month in which the product type is manufactured,
(iii) if the weekly amount manufactured is greater than 9 290 m2 but less than 18 581 m2, once a week per product type manufactured that week,
(iv) if the weekly amount manufactured is greater than or equal to 18 581 m2 but less than 37 161 m2, twice a week per product type manufactured that week, or
(v) if the weekly amount manufactured is greater than or equal to 37 161 m2, four times a week per product type manufactured that week;
(b) in the case of particleboard, medium-density fibreboard or thin medium-density fibreboard, for each production line or product type, once every eight or twelve hours, depending on shift length, plus or minus one hour; and
(c) in addition to the requirements specified in paragraphs (a) and (b), in the case of a composite wood panel or laminated product, once in any of the following circumstances:
(i) a change is made to the resin composition that increases the formaldehyde to urea ratio,
(ii) there is an increase of more than 10% in the amount of formaldehyde resin used per square metre or per composite wood panel or laminated product,
(iii) there is an increase of more than 20% in the adhesive application rate,
(iv) there is a decrease of more than 20% in the manufacturer’s established press time,
(v) the manufacturer believes that the emissions exceed the applicable limit set out in subsection 6(1) or the correlated limit referred to in subsection 6(2).
(3) The verification referred to in paragraph (1)(c) must be performed on a quarterly basis.
(4) For the purpose of paragraph (1)(b), the manufacturer must
(a) have an accredited laboratory establish the correlation of results in the manner set out in Section 3 of the Directive and have a third-party certifier verify the correlation; and
(b) have an accredited laboratory re-establish the correlation and a third-party certifier verify the re-established correlation in any of the following cases:
(i) a change is made to equipment, procedure or testing personnel that might affect test results,
(ii) formaldehyde emissions, when measured in two consecutive tests performed in accordance with paragraph 7(1)(b) for the same product type, exceed the applicable limit set out in subsection 6(1),
(iii) the results of one test performed in accordance with paragraph 7(1)(b), when compared with one test performed in accordance with paragraph 8(1)(b), do not correspond to the correlation established in accordance with paragraph (a) or re-established in accordance with this paragraph, as the case may be.
(5) A manufacturer of laminated products is not required to perform the selection and testing referred to in subsection (1) — or have the selection and testing performed — and have the testing verified for a product type if
(a) in the case of a product type whose core or platform is a composite wood panel, formaldehyde emissions from the core or platform, prior to incorporation into the laminated product, do not exceed the applicable limit set out in subsection 6(1) or the correlated limit referred to in subsection 6(2); and
(b) the veneer is glued to the core or platform using a phenol-formaldehyde resin or a no-added-formaldehyde resin.
(6) Despite paragraph (2)(b), a manufacturer of particleboard, medium-density fibreboard or thin medium-density fibreboard may perform the selection and testing — or have the selection and testing performed — in accordance with paragraphs (1)(a) and (b)
(a) once for every 24 hours of manufacturing if the average result of the 30 most recently performed tests on specimens of its product type remains two standard deviations below the applicable limit set out in subsection 6(1) or the correlated limit referred to in subsection 6(2) for the previous 60 days or more; and
(b) once for every 48 hours of manufacturing if the average result of the 30 most recently performed tests on specimens of its product type remains three standard deviations below the applicable limit set out in subsection 6(1) or the correlated limit referred to in subsection 6(2) for the previous 60 days or more.
Read the Formaldehyde Emissions from Composite Wood Products Regulations on the Justice Laws Website ↗
Made under Canadian Environmental Protection Act, 1999, S.C. 1999, c. 33.
Bills in Parliament that would change this section 0
No bill we hold would amend or repeal this section.