Large Fishing Vessel Inspection Regulations, C.R.C., c. 1435

Section 15

Cite as Large Fishing Vessel Inspection Regulations, C.R.C., c. 1435, s. 15 · current to July 24, 2025 · regulation last amended February 21, 2023

Statute Watch

Get an alert when a bill in Parliament would change this section, and every time it moves.

The text

(1) A fuel tank that is separate from the hull shall comply with the following: (a) the tank shall be made of steel or other material that, in the opinion of the Board, is suitable for the purpose; (b) the tank shall be constructed of material having a minimum thickness of plate of (i) 3 mm where the capacity of the tank is more than 114 L and not more than 1 364 L, (ii) 5 mm where the capacity of the tank is more than 1 364 L and not more than 4 550 L, and (iii) 6 mm where the capacity of the tank is more than 4 550 L; (c) where the capacity of a fuel tank does not exceed 114 L, it may be constructed of material that is less than 3 mm; (d) where the fuel tank referred to in paragraph (c) (i) is to be used for gasoline, (ii) has a capacity of more than 23 L, and (iii) is constructed of material that is not corrosive resistant,the tank shall be galvanized inside and outside by the hot dipped process after construction is completed; (e) where the capacity of a fuel tank is more than 114 L, it shall be fitted with stiffeners so that unsupported flat surfaces shall not exceed (i) 0.28 m2 where the thickness of the tank plating is 3 mm, (ii) 0.56 m2 where the thickness of the tank plating is 5 mm, (iii) 0.84 m2 where the thickness of the tank plating is 6 mm, and (iv) 1.12 m2 where the thickness of the tank plating is 8 mm; (f) where the thickness of the tank plating is intermediate to any set out in paragraph (b) the unsupported flat surface area shall be calculated by interpolation and where such thickness exceeds 8 mm, the unsupported flat surface area shall be calculated by a like progression as in paragraph (b) and by interpolation; (g) if considered necessary by the Board, baffle plates shall be fitted inside the tank; (h) a fuel tank having a capacity (i) exceeding 1 364 L and not exceeding 4 550 L shall be fitted with a suitable clean-out door, and (ii) exceeding 4 550 L shall be fitted with a manhole door; (i) the seams of a fuel tank shall be welded, brazed or double riveted, but soldered joints may be used on a tank having a capacity of not over 114 L if the solder has a melting point of not less than 427°C; (j) subject to paragraph (k), a fuel tank having a capacity exceeding 114 L shall be tested on completion by hydraulic pressure to a head of at least 2.44 m above the crown or to the maximum head to which the tank will be subjected, whichever is the greater, and the tests shall be witnessed by an inspector; and (k) in the case of any fuel tank having a capacity not exceeding 1 364 L, the inspector may, when it is not practicable for him to witness the test, accept a written statement from the manufacturer certifying that the hydraulic pressure test referred to in paragraph (j) has been carried out and that no defects were revealed. (2) Where the capacity of a fuel tank is more than 114 L, it shall be provided with (a) a filling pipe that (i) is at least 38 mm in internal diameter, (ii) leads from the top of the tank to the weatherdeck, the connection through the deck being watertight, (iii) is fitted with a screwed brass plug or cap, and (iv) is made sufficiently flexible to absorb any vibration or sinkage of the tank; and (b) a vent pipe that (i) leads from the top of the tank to a safe height and location above the weatherdeck, (ii) is clear of all openings into the hull or deck house, (iii) has the end of the pipe covered with wire gauze and turned down through an angle of 180 degrees, and (iv) has the deck connection watertight,but two or more vent pipes may be branched off from the pipe leading to the deck provided that the deck pipe is increased in diameter to maintain the required cross-sectional area, which area shall not be less than that of the filling pipe. (3) Each fuel tank shall be provided with a suitable means for ascertaining the level of the oil therein and if sounding pipes are fitted they shall be led to an accessible position on a deck above the load water line, but where this arrangement is not practicable, short sounding pipes may be fitted in the machinery spaces if they are led to readily accessible positions above the platforms and fitted with self-closing cocks or valves. (4) Glass tubing shall not be used as a gauge glass on a fuel tank having a capacity of more than 114 L or on any fuel tank that contains fuel having a flashpoint of less than 52°C (Pensky-Marten closed cup), but flat glass gauges of a type approved by the Board may be used on any fuel tank if fitted with self-closing cocks or valves. (5) Where glass tubing is used as a gauge on a fuel tank, the gauge shall be fitted with a cock or valve at the top and at the bottom. (6) Where a drain valve or cock is provided on a fuel tank, the drain valve or cock shall have a standard screwed outlet that shall be kept plugged with a screwed plug whenever the valve or cock is not in use. (7) In a new or existing fishing vessel, the piping from a fuel tank to a propelling engine shall be fitted with a valve or cock attached to that fuel tank. (8) The valve or cock referred to in subsection (7) shall be so controlled that it can be shut off from a position that is (a) outside the compartment in which the fuel tank is situated; and (b) always accessible in the event of fire taking place in the compartment in which the fuel tank is situated. (9) The means of remote control referred to in subsection (8) shall consist of (a) an extended spindle; (b) a self closing valve actuated by a trip wire; or (c) any other device satisfactory to an inspector. (10) The provisions of subsection (8) shall not apply to an existing fishing vessel where, in the opinion of an inspector, the fitting of a remote control to the fuel tank outlet valve or cock would be impracticable, but in such a case, means shall be provided whereby the propelling engine may be stopped from a position outside the compartment in which the propelling engine is situated. (11) Notwithstanding the provisions of subsection (10), where a new or existing fishing vessel is equipped with an oil fired power boiler for main or auxiliary steam, the provisions of subsection (8) shall apply to every fuel tank outlet valve or cock. (12) Subject to subsection (12.1), no fuel tank shall be located where, in the event of a fuel spillage or leakage, fuel could come into contact with a component that has a surface that is or may become heated. (12.1) Subject to subsection (12.2), where it is impracticable for a fuel tank in an existing fishing vessel to be located in accordance with subsection (12), a component referred to in subsection (12) shall be relocated to ensure that, in the event of a fuel leakage or spillage, no fuel will come into contact with the component. (12.2) Where it is impracticable to relocate a component referred to in subsection (12), protective plating and drip trays with drainage arrangements to a sump tank shall be fitted to ensure that, in the event of a fuel leakage or spillage, no fuel will come into contact with the component. (13) Means shall be provided to prevent the movement of oil fuel tanks when the fishing vessel is in a seaway. (14) Fuel tanks that are not separate from the hull shall be considered as part of the hull, taking into consideration the strength requirements of the vessel and the possibility of contamination of oil fuel with water, but the standards of construction and testing shall not be less than those given in this section for fuel tanks that are separate from the hull. (15) Means shall be provided to ensure that, in the event of fuel spillage or leakage from any source on a fishing vessel, no fuel will come into contact with any component that has a surface that is, or may become, heated.
Read the Large Fishing Vessel Inspection Regulations on the Justice Laws Website ↗

Made under Canada Shipping Act, 2001, S.C. 2001, c. 26.

Bills in Parliament that would change this section 0

No bill we hold would amend or repeal this section.